<div dir="ltr"><div><div><div><div><div><div>Paul,<br>Thanks for specifying where to type in the device name. <br></div>I had selected the option "hw: VSL" from this dropdown earlier and then moved the INPUT and OUTPUT selectors to "default". restarted jack, rebooted the station, etc. But Ardour3 would still not detect the microphone, so I went back and did re-select the specific INPUT and OUTPUT. I'm going to try this again, later on today, though and re-enstate defaults for INPUT and OUTPUT.<br></div><br></div>To restate the problem:<br></div>On a fresh install of Ubuntu studio,  I accept all the defaults when starting qjack, then Ardour3: <br>Ardour3 works perfectly and I can record from microphone that is fed through the presonus external sound card. I can add as many tracks and play them back no problem.<br><br></div>However on a system reboot (and subsequent reboots), the microphone is no longer detected at all, when I add a new audio track and cue record, for either an existing project or a new project, even though I have not changed the configuration.  Then I verify that qjack is set to see my soundcard (by name) as I have previously outlined, but Ardour3 still will not detect/record from the microphone going through the external sound card.<br><br></div><div>Cameron<br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Jun 24, 2015 at 8:03 AM, Paul Davis <span dir="ltr"><<a href="mailto:paul@linuxaudiosystems.com" target="_blank">paul@linuxaudiosystems.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><br><div class="gmail_extra"><br><div class="gmail_quote"><span class="">On Tue, Jun 23, 2015 at 10:15 PM, Cameron Metcalf <span dir="ltr"><<a href="mailto:podeas@gmail.com" target="_blank">podeas@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><div><div><div><div><div><div><div><div><div><div>Paul,<br></div>I re-traced my steps. I had definitely read through: <a href="http://jackaudio.org/faq/device_naming.html" target="_blank">http://jackaudio.org/faq/device_naming.html</a><br></div>a few times this past week and tried out (and have just RE-tried) the following (after each change below, I re-run qjack and boot up Ardour to see if the mic can be found)...<br><br></div>I run: <code>cat /proc/asound/cards<br><br></code></div><code>and get:<br>1 [VSL            ]: USB-Audio - AudioBox 22 VSL<br>                      PreSonus AudioBox 22 VSL at usb-0000:00:1d.7-3, high speed<br><br>--<br></code></div><br>The conclusion of the FAQ page informs: "You can type it into the device name selector in the upper left of qjacktl's
setup dialog."<br><br></div>I do not see anyplace in qjacktl where I can literally type in a device name selector. (I uninstalled an reinstalled qjacktl to try and look for this again in case anything had been botched from other things I'd changed).<br><br></div>After I click "setup" from qjacktl there is no place to type in a device name selector. However, in the "Settings" tab, there are two dropdown boxes for INPUT and OUTPU.  Both literally have "> hw:VSL" selected already. <br></div></div></div></div></div></blockquote><div><br></div></span><div>You should NOT use the INPUT or OUTPUT selectors. They should never have been displayed so prominently. You need the "Interface" selector near the upper right of the setup dialog.<br></div><span class=""><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><div><div><div><br></div>Out of desperation and just to see what would happen, I ran: <code>jackd -d alsa -d hw:VSL<br></code></div>from the command line. This did not resolve the problem.<br></div></div></div></blockquote><div><br></div></span><div>Well, that's correct. So I think you need to restate the problem ....<br></div><div> <br></div></div></div></div>
</blockquote></div><br></div>