<div dir="ltr"><div>Seems no one has something to say about this.....<br><br></div><div>I would expect it to be from one upwards if a strip is off or somehow inactive i would expect it to be there but non functional or it behaves like the GUI. Out of experience if there is a way in a program to present something to the user and adding another way it is best to stay with what they are used to or in that case with interfaces everyone counts up because they are used to.<br><br></div><div>As for sending well technically there would it would be possible to send after the bank change the current strip settings (maybe as a bulk?) with those strips not used with a value of zero and then not using them or not updating.<br><br></div><div>I would expect people to expect it that when pressing the bank up button that the interface shows the current settings of that bank. In the OSC specification I saw that it is possible to send bundles with several osc messages being sent at once but haven´t had a closer look at that or how to differentiate between bundle and normal single message.<br><br></div><div>If one is on the right or on the left should not matter. If you move a fader (or whatever it is ) you just have to set a pin on a H-bridge high read the pot and set the pin low when arriving meaning the important thing is the number of the strip it is then physically is up to the control surface. As example I have in my code put <br>master as  Fader0<br>Channel1 being Fader1<br>Channel1 + Banksize is Fader1 <br>(still needs adjustment as osc is not yet final).<br><br></div><div>Hope this gives a bit of help on that matter.<br><br></div><div>Regards<br><br></div><div>Melanie<br></div><div><div><div class="gmail_extra"><br><div class="gmail_quote">2016-06-21 20:31 GMT+02:00 Len Ovens <span dir="ltr"><<a href="mailto:len@ovenwerks.net" target="_blank">len@ovenwerks.net</a>></span>:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Are there any opinions on how the top bank should be displayed on a surface?<br>
<br>
In the MCP code (Mackie Control) I set it so that the bank start was always a mutiple of bank size. This means that after a bank, the left most strip is always the next strip after the right most strip in the previous bank. Some of the strips in the highest bank will therefore be blank/unused.<br>
<br>
The other way of doing things, is that the highest bank sets the rightmost strip to the highest strip number and fills back from there. All the strips are always used (so long as there are at least enough strips to do so). SO far this how the OSC code works.<br>
<br>
Those of you who use a control surface, do you find one way better than the other? Does anyone use their control surface with another daw and find Ardour does things different and that it is confusing switching back and forth?<br>
<br>
Probably both Surfaces should work the same, so I will change the one people don't like.<br>
<br>
--<br>
Len Ovens<br>
<a href="http://www.ovenwerks.net" rel="noreferrer" target="_blank">www.ovenwerks.net</a><br>
<br>
_______________________________________________<br>
ardour-dev mailing list<br>
<a href="mailto:ardour-dev@lists.ardour.org" target="_blank">ardour-dev@lists.ardour.org</a><br>
<a href="http://lists.ardour.org/listinfo.cgi/ardour-dev-ardour.org" rel="noreferrer" target="_blank">http://lists.ardour.org/listinfo.cgi/ardour-dev-ardour.org</a><br>
</blockquote></div><br></div></div></div></div>